Heated four-chamber rescue/community variant for up to eight cats, with a separate product-specific heating zone in each chamber.
Capacity8
Width2100 mm
Depth820 mm
Insulation50 mm
model v1.0.0compiler v1.8.0plan fd41682c73a6a388WINTER SEVEREreference outdoor scenario, not a rating -15 °C
Heating is not a DIY electrical specification. The model requires a compatible purpose-built product installed to its instructions.
Geometry
Dimensions and construction
Compiled drawing sheetRescue Modular Eight Heated
MODELrescue-cat-eight-heated-01
VERSIONv1.0.0
STATUSDATA VALIDATED
PLAN IDfd41682c73a6a388
This sheet is compiler-derived. Solid dimensions and chambers are geometry; framing/hardware elements marked PROVISIONAL remain design assumptions until engineering review.
External size
2100 × 820 × 760 mm
Rear height
670 mm
Ground clearance
160 mm
Entrance
150 × 180 mm × 4
Sill above finished floor
36 mm
Chambers
4
Wall thickness
71 mm
Floor assembly
74 mm
Roof assembly
71 mm
Roof vertical projection
70.6 mm
Clear wall height front/rear
615 / 525 mm
Roof angle
6.3°
Validation ladder
What is actually validated
Status is not promoted because the application looks finished. Each next level requires a new kind of evidence.
Current stateDATA VALIDATED
Model versionv1.0.0
Compilerv1.8.0
Plan IDfd41682c73a6a388
Sources in compiled plan11
01
Data and compiler gateDATA_VALIDATED
Schema, sources, assemblies, openings, stock fit, framing/hardware invariants and calculation outputs must remain internally consistent.
CURRENT
02
Geometry validatedGEOMETRY_VALIDATED
Requires recorded software and visual verification of 3D/drawings/cut parts, not merely successful data loading.
NOT VALIDATED
03
Engineering reviewENGINEERING_REVIEWED
Provisional framing, fastener, moisture, thermal and service details must be reviewed for the actual construction method.
NOT VALIDATED
04
Physical prototypePROTOTYPE_BUILT
A physical example exists with documented deviations, photographs and a final safety inspection.
NOT VALIDATED
05
Field validationFIELD_TESTED
The model has documented real-world use. Even this status is not a universal safe-temperature guarantee.
NOT VALIDATED
Thermal
Transparent thermal estimate
Steady-state envelope transmission estimate. It does not include a validated entrance-infiltration model and is not a temperature guarantee.
Wall U · nominal0.55 W/m²K0.50–0.61 W/m²K
Floor U · nominal0.54 W/m²K0.48–0.59 W/m²K
Roof U · nominal0.56 W/m²K0.51–0.62 W/m²K
ΔT comparison20 Kmethod v1.2.0
Nominal envelope transmission74 W67–81 W
Wall Rsi0.13 m²K/Whorizontal heat flow
Roof Rsi0.10 m²K/Wupward heat flow
Floor Rsi0.17 m²K/Wdownward heat flow
Rse0.04 m²K/WISO 6946 · v1.2.0
ΔT explorerScenario temperature difference
Nominal transmission74 W
Sensitivity band67–81 W
This only scales steady-state transmission through wall/floor/roof. ΔT is not an outdoor temperature or guaranteed indoor temperature; infiltration, wind, framing thermal bridges and other effects are not added.
Current model limitations
No validated entrance infiltration model
No validated airflow model for the provisional ventilation insert zones
No wind pressure model
No animal metabolic heat credit
No transient heat-storage model
No 2D framing thermal-bridge correction
No explicit corner/end-grain edge-return thermal-bridge model
Ventilation · PROVISIONAL
Reserved high-rear zones
These are not prescribed vent-opening dimensions. The compiler only reserves zones that avoid provisional framing; the actual cutout and net free area remain specific to the selected adjustable vent insert and physical validation.
StrategyHIGH REAR
Zone per chamber1
Top clearance53 mm
Actual openingTBD by insert
Chamber 196 × 42 mm
Center X
167 mm
Bottom above finished floor
430 mm
Status
ASSUMPTION
Chamber 296 × 42 mm
Center X
660 mm
Bottom above finished floor
430 mm
Status
ASSUMPTION
Chamber 396 × 42 mm
Center X
1152 mm
Bottom above finished floor
430 mm
Status
ASSUMPTION
Chamber 496 × 42 mm
Center X
1933 mm
Bottom above finished floor
430 mm
Status
ASSUMPTION
V1 model boundary
The zone is a coordination reserve, not proof of adequate ventilation. After construction, condensation, odor/moisture and local drafts must be checked; the actual vent insert or its setting may need adjustment.
Heating · PRODUCT_SPECIFIC
Purpose-built heating zones
The compiler reserves one zone in each chamber, but does not specify power, voltage, thermostat behavior or improvised wiring. The selected product must be purpose-built for animals and installed to its own instructions.
Chamber 1264 × 271 mm
Floor coverage
22%
Unheated choice area
0.25 m²
Position
X 179 / Z 424 mm
Chamber 2264 × 271 mm
Floor coverage
22%
Unheated choice area
0.25 m²
Position
X 672 / Z 424 mm
Chamber 3264 × 271 mm
Floor coverage
22%
Unheated choice area
0.25 m²
Position
X 1164 / Z 424 mm
Chamber 4264 × 271 mm
Floor coverage
22%
Unheated choice area
0.25 m²
Position
X 1657 / Z 424 mm
No DIY mains heating
Zones are coordination geometry, not an electrical design. Adapters, controllers and unprotected connections do not belong in the animal space. Cable-entry BOM items only reserve protected routing for a selected compatible product.
Exterior plywood · 12 mm9.92 m²net area of actual cut geometry
Exterior plywood · 9 mm4.64 m²net area of actual cut geometry
XPS insulation · 50 mm6.51 m²net area of actual cut geometry
Sheet planning · deterministic V1
Sheet layout
Actual part geometry is shown with a solid outline while the dashed rectangle is the conservative packing envelope. V1 still packs trapezoids by bounding box, so it is not polygon-optimal nesting. Material % measures actual part area; envelope % is the space reserved by the algorithm.
2500 × 1250 mm · kerf 3 mm · margin 10 mm
Plywood 12 mm
6sheets / boards
Sheet 172% material · 72% envelopeSheet 255% material · 55% envelopeSheet 355% material · 55% envelopeSheet 473% material · 77% envelopeSheet 550% material · 53% envelopeSheet 612% material · 13% envelope
2500 × 1250 mm · kerf 3 mm · margin 10 mm
Plywood 9 mm
3sheets / boards
Sheet 155% material · 55% envelopeSheet 268% material · 71% envelopeSheet 325% material · 26% envelope
1250 × 600 mm · kerf 2 mm · margin 5 mm
XPS insulation
18sheets / boards
Sheet 157% material · 57% envelopeSheet 257% material · 57% envelopeSheet 357% material · 57% envelopeSheet 457% material · 57% envelopeSheet 558% material · 58% envelopeSheet 658% material · 58% envelopeSheet 758% material · 58% envelopeSheet 858% material · 58% envelopeSheet 940% material · 40% envelopeSheet 1040% material · 40% envelopeSheet 1140% material · 40% envelopeSheet 1240% material · 40% envelopeSheet 1370% material · 70% envelopeSheet 1470% material · 70% envelopeSheet 1527% material · 27% envelopeSheet 1627% material · 27% envelopeSheet 1727% material · 27% envelopeSheet 1827% material · 27% envelope
Local price profile
Cost estimate
Quantities come from the model. Prices are not fabricated: enter what you actually pay locally and the estimate stays in your browser.
Plywood 12 mmSheet count from the 2500 × 1250 mm nesting layout.
6 sheetRSD 0
Plywood 9 mmSheet count from the 2500 × 1250 mm nesting layout.
3 sheetRSD 0
XPS 50 mmBoard count from the planning stock size 1250 × 600 mm. Verify dimensions with the local supplier.
18 sheetRSD 0
Roof waterproofingFull sloped roof panel area + 15% allowance for overlap and waste.
2.59 m²RSD 0
Exterior wood protectionExterior wall and floor-underside area + 10% allowance. Coat count and coverage depend on the selected non-toxic exterior product.
5.44 m²RSD 0
Adjustable ventilation insertsOne selected insert for each PROVISION zone. Final cutout and net free area must follow the selected product data sheet.
4 itemRSD 0
Timber framing 30 × 50 mm + base 45 × 45 mmTotal framing schedule length + 10% allowance. Profiles remain PROVISIONAL until engineering review.
42.05 mRSD 0
Base isolation pads / feetOne suitable isolation foot or pad below each V1 vertical support so timber does not bear directly on wet ground. Product selection, anchorage and capacity depend on the actual site and substrate.
6 itemRSD 0
Exterior corner weather trimPlanning length for the four vertical exterior corner edges. Profile, sealing and overlap must be compatible with the selected exterior sheathing and finish system.
2.28 mRSD 0
Exterior wood-panel fastenersV1 estimate uses approximately 150 mm edge spacing and 300 mm field spacing as a reference starting pattern. Final diameter, length and schedule remain subject to engineering review.
628 itemRSD 0
Exterior roof hingesCount is derived from roof width. The hinge axis sits on the front-wall line, inset from the outer front edge by the roof overhang. Verify final hinge type and load capacity before ENGINEERING_REVIEWED status.
4 itemRSD 0
Roof latchesIntended to secure the service roof against wind uplift. Latches sit on the rear-wall line, inset from the outer runoff edge by the rear overhang so the exterior drip path remains clear.
2 itemRSD 0
Roof edge / drip protectionPlanning length for the full roof-panel perimeter. Final profile, layer order and low rear-edge detail must follow the selected roofing system.
6.49 mRSD 0
Service-roof weather sealLength is derived from shelter perimeter; final seal profile depends on the joint detail.
5.84 mRSD 0
Protected cable entryOnly for a purpose-built pet-heating product and its instructions; the app does not specify DIY mains wiring.
4 itemRSD 0
Purpose-built pet heating productPlanning quantity assumes one compatible purpose-built product per compiled heating zone. If a selected certified system explicitly serves multiple zones, actual procurement follows its product data. The app does not design an improvised heater.
4 itemRSD 0
Estimate from entered pricesRSD 0
Sheet, XPS, framing and hardware quantities come from the compiler. The estimate still excludes delivery, tools, labor, local taxes and unforeseen losses beyond the stated allowances. PROVISIONAL and product-specific items remain explicitly labeled.
Operation & welfare
How to use the model in winter
Construction alone is not enough. Placement, moisture, bedding, weather and routine inspection directly affect real-world shelter performance.
Place the shelter in a protected location away from direct wind and predator hazards.
Keep it elevated and dry; the entrance should not sit at wet-ground or snow level.
For community cats, use straw as winter bedding; towels and blankets can retain moisture.
Multiple entrances add an escape route but also increase cold-air exchange, making entrance protection more important.
After snow or heavy rain, check the entrance, bedding dryness and shelter stability.
Watch for condensation and moisture near the upper zone. The PROVISION ventilation zone is not a predefined opening; the selected insert should be adjusted so it does not create a direct local draft.
side-outerExterior side panelstrapezoid profile · The side wall fits between the full-width front and rear walls. Clear length 678 mm; front inner edge 608 mm; rear inner edge 533 mm.678 × Hf 608 / Hr 533 × 12 mm2
xps-front-r1c1Front-wall XPSxps · Trim entrance openings after dry fitting against the compiled front-panel cutouts.979 × 304 × 50 mm1
xps-front-r1c2Front-wall XPSxps · Trim entrance openings after dry fitting against the compiled front-panel cutouts.979 × 304 × 50 mm1
xps-front-r2c1Front-wall XPSxps · Trim entrance openings after dry fitting against the compiled front-panel cutouts.979 × 303.6 × 50 mm1
xps-front-r2c2Front-wall XPSxps · Trim entrance openings after dry fitting against the compiled front-panel cutouts.979 × 303.6 × 50 mm1
xps-rear-r1c1Rear-wall XPSxps979 × 533.2 × 50 mm1
xps-rear-r1c2Rear-wall XPSxps979 × 533.2 × 50 mm1
xps-side-a-r1c1Side-wall XPS Axps · Final top edge follows the roof slope down to 533.2 mm.678 × 304 × 50 mm1
xps-side-a-r2c1Side-wall XPS Axps · Final top edge follows the roof slope down to 533.2 mm.678 × 303.6 × 50 mm1
xps-side-b-r1c1Side-wall XPS Bxps · Final top edge follows the roof slope down to 533.2 mm.678 × 304 × 50 mm1
xps-side-b-r2c1Side-wall XPS Bxps · Final top edge follows the roof slope down to 533.2 mm.678 × 303.6 × 50 mm1
xps-floor-r1c1Floor XPSxps1050 × 410 × 50 mm1
xps-floor-r1c2Floor XPSxps1050 × 410 × 50 mm1
xps-floor-r2c1Floor XPSxps1050 × 410 × 50 mm1
xps-floor-r2c2Floor XPSxps1050 × 410 × 50 mm1
xps-roof-r1c1Roof XPSxps1050 × 413 × 50 mm1
xps-roof-r1c2Roof XPSxps1050 × 413 × 50 mm1
xps-roof-r2c1Roof XPSxps1050 × 412 × 50 mm1
xps-roof-r2c2Roof XPSxps1050 × 412 × 50 mm1
dividerInterior dividertrapezoid profile · Front clear edge 607.6 mm; rear clear edge 533.2 mm. Cut the top edge to the compiled roof slope.678 × Hf 607.6 / Hr 533.2 × 12 mm3
Framing · PROVISIONAL
Framing and support schedule
Lengths are derived from model geometry. Frame and base profiles are a V1 design assumption and remain explicitly PROVISIONAL until engineering review and physical validation.
Quantities and geometry are a V1 workshop plan. Fastener spacing uses an APA reference pattern as a conservative starting point, but it is not a certified fastening design for this product.
Edge spacing≈ 150 mm
Field spacing≈ 300 mm
Panel joint gap3 mm
Roof slope6.3°
Runoff edgerear
Rear drip edge2.24 m
Hinge axis from front edge91 mm
Latch axis from front edge915 mm
IDItemQuantityStatus
base-isolation-padsBase isolation pads / feetOne suitable isolation foot or pad below each V1 vertical support so timber does not bear directly on wet ground. Product selection, anchorage and capacity depend on the actual site and substrate.6 pcsASSUMPTION
corner-weather-trimExterior corner weather trimPlanning length for the four vertical exterior corner edges. Profile, sealing and overlap must be compatible with the selected exterior sheathing and finish system.2.28 mASSUMPTION
panel-fastenersExterior wood-panel fastenersV1 estimate uses approximately 150 mm edge spacing and 300 mm field spacing as a reference starting pattern. Final diameter, length and schedule remain subject to engineering review.628 pcsASSUMPTION
roof-hingesExterior roof hingesCount is derived from roof width. The hinge axis sits on the front-wall line, inset from the outer front edge by the roof overhang. Verify final hinge type and load capacity before ENGINEERING_REVIEWED status.4 pcsASSUMPTION
roof-latchesRoof latchesIntended to secure the service roof against wind uplift. Latches sit on the rear-wall line, inset from the outer runoff edge by the rear overhang so the exterior drip path remains clear.2 pcsASSUMPTION
roof-edge-weathering-profileRoof edge / drip protectionPlanning length for the full roof-panel perimeter. Final profile, layer order and low rear-edge detail must follow the selected roofing system.6.49 mASSUMPTION
roof-weather-sealService-roof weather sealLength is derived from shelter perimeter; final seal profile depends on the joint detail.5.84 mGEOMETRY
protected-cable-entryProtected cable entryOnly for a purpose-built pet-heating product and its instructions; the app does not specify DIY mains wiring.4 pcsASSUMPTION
Steps follow the model configuration. Heated variants automatically include a dedicated step constrained to purpose-built equipment.
0 / 10steps completed
Build the raised base
Assemble the compiled grid of vertical supports and horizontal runners. Use a suitable isolation foot/pad below each support to keep timber off wet ground; adapt anchorage and bearing details to the actual site.
Assemble the insulated floor
Enclose the insulation between lower and interior floor panels so the animal cannot access it.
Assemble walls to the compiled joinery plan
Front and rear walls remain full width while side walls fit between their inner planes. Use the compiled side lengths/heights and entrance dimensions; do not extend side panels through the corner zones.
Weather-protect the four exterior corner edges
Install compatible exterior corner trim/sealing over the vertical joints so cut panel edges are not exposed to water. The selected trim and overlap must follow the exterior finish system.
Reserve the high-rear ventilation insert zones
Transfer the compiled PROVISIONAL zones to the rear wall and keep them clear of studs. Do not cut the final opening until a specific adjustable vent insert is selected; its cutout and net free area are product-specific.
Install insulation and interior linings
Dry-fit the XPS, enclose it with the interior linings and confirm that no insulation edge is accessible to the animal.
Install interior dividers
Position dividers on the axes between the corresponding entrances, verify stability and seal every sharp edge.
Install roof and waterproofing
The roof falls from front to rear, making the rear edge the natural runoff edge. Select a roofing system that explicitly permits the compiled slope, follow its layer/overlap instructions and detail edge/drip protection so water sheds behind the shelter, away from entrances.
Install a compatible purpose-built heating product
Follow the heating product manufacturer instructions; mains adapters and unprotected connections do not belong in the animal space.
Perform the final safety inspection
Check stability, sharp edges, water ingress, ventilation, entrances and interior dryness.
Provenance
Sources and limitations
A source supports a method or welfare guideline; it does not turn this specific model into a certified product. Physical validation has a separate status.
Notes stay only in this browser and are tied to the exact Plan ID. Completing the worksheet does not promote the public model state - it creates an evidence trail for future physical validation.
MODELrescue-cat-eight-heated-01
MODEL VERSIONv1.0.0
COMPILERv1.8.0
PLAN IDfd41682c73a6a388
Recorded checks0 / 10
This worksheet is not a certificate, veterinary assessment or automatic FIELD_TESTED state. The published validation state changes only after separate review of real evidence.